Comelit SimpleHome

The Comelit SimpleHome integrationIntegrations connect and integrate Home Assistant with your devices, services, and more. [Learn more] allows you to control your Comelit home automation devices.

The integration provides information on connected devices and enables control of the alarm system.

Supported devices

There is support for the following devices within Home Assistant:

  • Comelit Serial Bridge
  • Comelit VEDO System

Configuration

To add the Comelit SimpleHome hub to your Home Assistant instance, use this My button:

Manual configuration steps

If the above My button doesn’t work, you can also perform the following steps manually:

  • Browse to your Home Assistant instance.

  • Go to Settings > Devices & services.

  • In the bottom right corner, select the Add Integration button.

  • From the list, select Comelit SimpleHome.

  • Follow the instructions on screen to complete the setup.

host

The IP address of the Comelit SmartHome device.

port

The TCP port of the Comelit SmartHome device. The default is port 80 (standard for HTTP).

pin

The PIN of the Comelit SmartHome device.

type

The type of Comelit SmartHome device.

bridge

Comelit Serial Bridge.

vedo

Comelit VEDO System.

Configuration options

Options

To define options for Comelit SimpleHome, follow these steps:

  1. In Home Assistant, go to Settings > Devices & services.

  2. If multiple instances of Comelit SimpleHome are configured, choose the instance you want to configure.

  3. On the card, select the cogwheel .

    • If the card does not have a cogwheel, the integration does not support options for this device.

    Screenshot showing the cogwheel icon on an integration card in the Settings > Devices & services page

  4. Edit the options, then select Submit to save the changes.

The device does not report how long a cover takes to fully open or close, so Home Assistant estimates its position based on the elapsed time since it started moving. You can set this travel time individually for each cover, since it depends on the type of cover, for example, a window opens and closes faster than a door-height shutter.

  1. Select the cover you want to configure.
  2. Enter the estimated time it takes for the cover to fully open or close.
  3. Select Submit to save the changes.
Cover

The cover entityAn entity represents a sensor, actor, or function in Home Assistant. Entities are used to monitor physical properties or to control other entities. An entity is usually part of a device or a service. [Learn more] to set the travel time for.

Travel time

The estimated time, in seconds, for the cover to fully open or close. Enter a value between 1 and 120 seconds. The default is 25 seconds.

Examples

Automation: Activate the alarm when you leave home

automation:
- alias: "Arm alarm away"
  id: "arm_alarm_away"
  triggers:
    - trigger: zone.occupancy_cleared
      options:
        zone: zone.home
  actions:
    - action: alarm_control_panel.alarm_arm_away
      target:
        entity_id: alarm_control_panel.home
      data:
        code: "12345"

Automation: Close the covers at sunset if you are not at home

automation:
- alias: Close covers at sunset
  id: "covers_close_sunset"
  trigger:
   - trigger: sun.sunset
  condition:
    conditions:
      - alias: "condition alias (not home)"
        condition: zone.occupancy_is_not_detected
        options:
          zone: zone.home
  actions:
    entity_id:
      - cover.group_home_covers
    action: cover.close_cover

Data updates

This integration pollsData polling is the process of querying a device or service at regular intervals to check for updates or retrieve data. By defining a custom polling interval, you can control how frequently your system checks for new data, which can help optimize performance and reduce unnecessary network traffic. [Learn more] data from the device every 5 seconds by default.

Supported functionality

The Comelit SimpleHome integrationIntegrations connect and integrate Home Assistant with your devices, services, and more. [Learn more] provides the following entities:

Comelit Serial Bridge

  • Climate
  • Cover - open, close, stop, and set position
  • Dehumidifier
  • Humidifier
  • Light
  • Sensor - power consumption
  • Switch - irrigation and sockets (other)

Comelit VEDO System

  • Alarm control panel - per area
  • Binary sensor - per zone presence detection
  • Sensor - per zone status

Troubleshooting

Can’t set up the device

Symptom: “Cannot connect”

When trying to set up the integration, the form shows the message “Cannot connect”.

Description

This means that the IP address or the port specified is wrong.

Resolution

To resolve this issue, verify the device’s IP address and port by navigating to them in a web browser.

Can’t update data

Symptom: Device storage error

During data refresh, the device may fail to provide the expected data and logs the error above. In most cases, the device web UI shows some or all pages as blank.

Description

This usually indicates that the SD card is failing and can no longer be read reliably. One of the most commonly affected files is DATA\BPAGES.BIN.

Resolution

To resolve this issue, replace the SD card. If a backup is not available, restore the configuration and firmware using Comelit SimpleProg.

Removing the integration

This integration follows standard integration removal. No extra steps are required.

To remove an integration instance from Home Assistant

  1. Go to Settings > Devices & services and select the integration card.
  2. Next to the entry you want to remove, select the three dots menu. Then, select Delete.
    • Depending on the integration, the entries are listed under one of the following headings:
      • Devices
      • Hubs
      • Services
      • Integration entries
  3. To confirm, select Delete.
    • Home Assistant also deletes the devices and entities of the entry.
  4. If Home Assistant asks you to restart, restart Home Assistant.
  5. If Home Assistant asks whether to also delete the application credentials, select Remove or Keep.