Logitech Harmony Hub

The harmony integration allows you to control the state of your Harmony Hub Device.

Supported units:

  • Harmony Hub
  • Harmony Companion
  • Harmony Pro
  • Harmony Elite
  • Harmony Pro 2400

Configuration

To add the Logitech Harmony Hub integration to your Home Assistant instance, use this My button:

Logitech Harmony Hub can be auto-discovered by Home Assistant. If an instance was found, it will be shown as Discovered. You can then set it up right away.

Manual configuration steps

If it wasn’t discovered automatically, don’t worry! You can set up a manual integration entry:

  • Browse to your Home Assistant instance.

  • Go to Settings > Devices & Services.

  • In the bottom right corner, select the Add Integration button.

  • From the list, select Logitech Harmony Hub.

  • Follow the instructions on screen to complete the setup.

Note: Depending on the firmware, you may need to enable XMPP for this integration to work. From your Harmony app, go to: Menu > Harmony Setup > Add/Edit Devices & Activities > Remote & Hub > Enable XMPP.

Once the Logitech Harmony Hub has been configured, the default activity and duration in seconds between sending commands to a device can be adjusted in the settings via Settings -> Devices & services >> Your Logitech Harmony Hub

Configuration file

Upon startup one file will be written to your Home Assistant configuration directory per device in the following format: harmony_UNIQUE_ID.conf. The file will contain:

  • List of all programmed activity names and ID numbers
  • List of all programmed device names and ID numbers
  • List of all available commands per programmed device

This file will be overwritten whenever the Harmony HUB has a new configuration, there is no need to restart Home Assistant.

Action remote.turn_off

Turn off all devices that were switched on from the start of the current activity.

Data attribute Optional Description
entity_id no Entity ID to target.

Action remote.turn_on

Start an activity. Will start the default activity from configuration.yamlThe configuration.yaml file is the main configuration file for Home Assistant. It lists the integrations to be loaded and their specific configurations. In some cases, the configuration needs to be edited manually directly in the configuration.yaml file. Most integrations can be configured in the UI. [Learn more] if no activity is specified. The specified activity can either be the activity name or the activity ID from the configuration file written to your Home Assistant configuration directory.

Data attribute Optional Description
entity_id no Entity ID to target.
activity yes Activity ID or Activity Name to start.

Example

In the file ‘harmony_REMOTENAME.conf’ you can find the available activities, for example:

{
    "Activities": {
        "-1": "PowerOff",
        "20995306": "Watch TV",
        "20995307": "Play Games",
        "20995308": "Listen Music"
    }
}

Using the activity name ‘Watch TV’, you can perform an action via automation to switch this activity on:

actions:
  - action: remote.turn_on
    target:
      entity_id: remote.bed_room_hub
    data:
       activity: "Watch TV"

Action remote.send_command

Send a single command or a set of commands to one device, device ID and available commands are written to the configuration file at startup. You can optionally specify the number of times you wish to repeat the command(s) and delay you want between repeated command(s).

Data attribute Optional Description
entity_id no Entity ID to target.
device no Device ID or Device Name to send the command to.
command no A single command or a list of commands to send.
num_repeats yes The number of times to repeat the command(s).
delay_secs yes The number of seconds between sending each command.

In the file ‘harmony_REMOTENAME.conf’ you can find the available devices and commands, for example:

{
    "Devices": {
        "TV": {
            "commands": [
                "PowerOff",
                "PowerOn"
            ],
            "id": "327297814"
        },
        "Receiver": {
            "commands": [
                "PowerOff",
                "PowerOn",
                "VolumeUp",
                "VolumeDown",
                "Mute"
            ],
            "id": "428297615"
        }
    }
}

A typical action for sending several button presses looks like this:

action: remote.send_command
target:
  entity_id: remote.tv_room
data:
  command:
    - PowerOn
    - Mute
  device: Receiver
  delay_secs: 0.6

OR

action: remote.send_command
target:
  entity_id: remote.tv_room
data:
  command:
    - PowerOn
    - Mute
  device: 428297615
  delay_secs: 0.6

Action harmony.change_channel

Sends the change channel command to the Harmony HUB

Data attribute Optional Description
entity_id no Entity ID to target.
channel no Channel number to change to

A typical action for changing the channel would be::

action: harmony.change_channel
target:
  entity_id: remote.tv_room
data:
  channel: 200

Action harmony.sync

Force synchronization between the Harmony device and the Harmony cloud.

Data attribute Optional Description
entity_id no Entity ID to target.

Examples

Template sensors can be utilized to display current activity in the frontend.

template:
  - sensor:
    - name: 'Family Room Harmony Remote'
      state: >
        {{ state_attr('remote.family_room', 'current_activity') }}
    - name: 'Bedroom Harmony Remote'
      state: >
        {{ state_attr('remote.bedroom', 'current_activity') }}

The example below shows how to control an input_boolean switch using the Harmony remote’s current activity. The switch will turn on when the remote’s state changes and the Kodi activity is started and off when the remote’s state changes and the current activity is “PowerOff”.

automation:
  - alias: "Watch TV started from harmony hub"
    triggers:
      - trigger: state
        entity_id: remote.family_room
    conditions:
      - condition: template
        value_template: '{{ trigger.to_state.attributes.current_activity == "Kodi" }}'
    actions:
      - action: input_boolean.turn_on
        target:
          entity_id: input_boolean.notify
  - alias: "PowerOff started from harmony hub"
    triggers:
      - trigger: state
        entity_id: remote.family_room
    conditions:
      - condition: template
        value_template: '{{ trigger.to_state.attributes.current_activity == "PowerOff" }}'
    actions:
      - action: input_boolean.turn_off
        target:
          entity_id: input_boolean.notify