JVC Projector

The JVC Projector integrationIntegrations connect and integrate Home Assistant with your devices, services, and more. [Learn more] lets you control and automate JVC projectors from Home Assistant. You can turn the projector on and off, send remote commands, change settings such as the input and picture mode, and use the power status and signal information in automations.

Supported devices

The integration supports JVC D-ILA projectors with a LAN port, including the following models and their regional variants:

  • DLA-NZ900 and NZ800 (DLA-RS4200 and RS3200)
  • DLA-NZ700 and NZ500 (DLA-RS2200 and RS1200)
  • DLA-NZ9, NZ8, NZ7, and NP5 (DLA-RS4100, RS3100, RS2100, and RS1100)
  • DLA-NX9, NX7, and NX5 (DLA-RS3000, RS2000, and RS1000)
  • DLA-Z1 (DLA-RS4500)
  • DLA-X990R, X970R, X790R, X770R, X590R, and X570R (DLA-RS640, RS620, RS540, RS520, RS440, and RS420)
  • DLA-X950R, X750R, and X550R (DLA-RS600, RS500, and RS400)
  • DLA-X900R, X700R, and X500R (DLA-RS67, RS57, and RS49)
  • DLA-X95R, X75R, X55R, and X35 (DLA-RS66, RS56, RS48, and RS46)
  • DLA-X90R, X70R, and X30 (DLA-RS65, RS55, and RS45)

A projector that the integration does not recognize gets basic support only: the Power binary sensor, the Status and Light Time sensors, the Input select, and the remote.

Prerequisites

  1. Connect the projector’s LAN port to the same network as Home Assistant, and note the projector’s IP address.
  2. Some JVC projectors require a network password before they accept network control. If your projector uses one, have it ready. You set the password in the projector’s network settings.

Configuration

To add the JVC Projector device to your Home Assistant instance, use this My button:

Manual configuration steps

If the above My button doesn’t work, you can also perform the following steps manually:

  • Browse to your Home Assistant instance.

  • Go to Settings > Devices & services.

  • In the bottom right corner, select the Add Integration button.

  • From the list, select JVC Projector.

  • Follow the instructions on screen to complete the setup.

Host

The IP address or hostname of the projector.

Port

The network control port of the projector. The default is 20554. Only change it if you changed the communication port on the projector.

Password

The network password of the projector. Leave it empty if the projector does not use a network password.

If the password on the projector changes, Home Assistant asks you to enter the new one.

Supported functionality

The JVC Projector integration creates a device for the projector. The device information shows the projector’s model code, firmware version, and MAC address. The model code is JVC’s internal code for the model, such as B5A2 for the DLA-NZ8.

The integration provides the following entities. Entities for features that your model does not support are not created.

Remote

The integration creates a remote entity for the projector. It turns the projector on and off, and you can use it with the Send remote command action to send the following commands.

Navigation:

  • menu, advanced-menu
  • up, down, left, right
  • ok, back
  • info, hide

Input:

  • input
  • hdmi1, hdmi2

Picture:

  • picture-mode, picture-adjust
  • natural, cinema
  • mode-1 through mode-10
  • color-profile, color-temp
  • gamma, gamma-settings
  • mpc, cmd

Lens and installation:

  • lens-control, lens-aperture
  • anamorphic
  • setting-memory

3D:

  • 3d-format

For example, this action opens the projector menu:

ActionAn action makes Home Assistant do something, for example, turn on a light, send a notification, or activate a scene. Automations and scripts run a list of actions. [Learn more]
action: remote.send_command
target:
  entity_id: remote.jvc_projector
data:
  command: menu

Binary sensors

  • Power
    • Description: Whether the projector is on. It is on while the Status sensor shows On or Warming, and off otherwise.
    • Available for models: all

Sensors

  • Status
    • Description: The power status of the projector: On, Warming, Cooling, Standby, or Error.
    • Available for models: all
  • Light Time
    • Description: How long the light source (lamp or laser) has been used.
    • Unit: h
    • Available for models: all
  • Color Depth
    • Description: The color depth of the input signal.
    • Available for models: all
    • Remarks: Disabled by default.
  • Color Space
    • Description: The color space of the input signal.
    • Available for models: DLA-X500R, X700R, X900R, and newer
    • Remarks: Disabled by default.
  • HDR
    • Description: The HDR format of the input signal.
    • Available for models: DLA-Z1, and the DLA-NX, NP, and NZ series
    • Remarks: Disabled by default.
  • Resolution
    • Description: The resolution of the input signal.
    • Available for models: all
    • Remarks: Disabled by default.
  • Colorimetry
    • Description: The colorimetry of the input signal, such as BT.709 or BT.2020.
    • Available for models: DLA-Z1, and the DLA-NX, NP, and NZ series
    • Remarks: Disabled by default.
  • Link Rate
    • Description: The HDMI link rate and lane configuration of the input signal.
    • Available for models: DLA-NP and NZ series
    • Remarks: Disabled by default.

Selects

The options of some selects depend on the model.

  • Input
    • Description: The HDMI input.
    • Options: HDMI 1, HDMI 2
    • Available for models: all
  • Installation Mode
    • Description: The installation mode.
    • Available for models: all
    • Remarks: Disabled by default.
  • Light Power
    • Description: The power level of the light source.
    • Available for models: all
    • Remarks: Disabled by default.
  • Dynamic Control
    • Description: The dynamic control setting.
    • Available for models: DLA-Z1 and the DLA-NZ series
    • Remarks: Disabled by default.
  • Clear Motion Drive
    • Description: The Clear Motion Drive setting.
    • Available for models: all
    • Remarks: Disabled by default.
  • Motion Enhance
    • Description: The Motion Enhance setting.
    • Options: High, Low, Off
    • Available for models: DLA-X550R, X750R, X950R, and newer, except the DLA-NZ500 and NZ700
    • Remarks: Disabled by default.
  • Anamorphic
    • Description: The anamorphic setting.
    • Available for models: all
    • Remarks: Disabled by default.
  • HDR Processing
    • Description: The HDR processing setting.
    • Available for models: DLA-NX, NP, and NZ series
    • Remarks: Disabled by default.
  • Picture Mode
    • Description: The picture mode.
    • Available for models: all
    • Remarks: Disabled by default.

Switches

  • E-Shift
    • Description: Turns E-Shift on or off.
    • Available for models: DLA-X500R, X700R, X900R, and newer, except the DLA-NX5, NX7, NP5, NZ500, and NZ700
    • Remarks: Disabled by default.
  • Low latency mode
    • Description: Turns low latency mode on or off.
    • Available for models: DLA-X570R, X770R, X970R, and newer, except the DLA-NZ500 and NZ700
    • Remarks: Disabled by default.

JVC Projector automation examples

Tip

You don’t need to edit YAML to use these examples. Copy a YAML snippet from this page, open the visual automation editor in Home Assistant, and press Ctrl+V (or Cmd+V on Mac). Home Assistant automatically converts the pasted YAML into the visual editor format, whether it’s a full automation, a single trigger, a condition, or an action.

Automation: Dim the lights when the projector turns on

This automation activates a lighting scene when the Power binary sensor turns on.

  • Trigger: Entity: State
    • Target: JVC Projector Power (binary_sensor.jvc_projector_power)
    • To: On
  • Action: Activate scene
    • Target: Theater lights (scene.theater_lights)
YAML example for dimming the lights when the projector turns on
AutomationAutomations in Home Assistant allow you to automatically respond to things that happen in and around your home. [Learn more]
alias: "Dim the lights when the projector turns on"
triggers:
  - trigger: state
    entity_id: binary_sensor.jvc_projector_power
    to: "on"
actions:
  - action: scene.turn_on
    target:
      entity_id: scene.theater_lights

Data updates

The integration pollsData polling is the process of querying a device or service at regular intervals to check for updates or retrieve data. By defining a custom polling interval, you can control how frequently your system checks for new data, which can help optimize performance and reduce unnecessary network traffic. [Learn more] the projector every 5 seconds while it is on, warming up, or cooling down, and every 10 seconds while it is in standby. The Input select and Light Time sensor are only updated while the projector is on. The other settings and the signal information are only updated while the projector is on and receiving a signal. When the signal is lost, they are cleared until a signal returns.

Known limitations

  • The projector accepts one network control connection at a time. Another controller that keeps a connection open, such as a control system or calibration software, can cause connection errors.

Troubleshooting

Failed to connect

Symptom: “Failed to connect”

When you set up the integration, the form shows the message “Failed to connect”.

Description

Home Assistant cannot reach the projector at the host and port you entered.

Resolution

  1. Make sure the projector is plugged in and its LAN port is connected to the same network as Home Assistant.
  2. Check the Host and Port you entered.
  3. Make sure no other controller is connected to the projector. See Known limitations.
Invalid authentication

Symptom: “Invalid authentication”

When you set up the integration, the form shows the message “Invalid authentication”.

Description

The password you entered does not match the network password set on the projector.

Resolution

  1. Check the network password in the projector’s network settings.
  2. Enter the same password in the Password field.

Removing the integration

This integration follows standard integration removal. No extra steps are required.

To remove an integration instance from Home Assistant

  1. Go to Settings > Devices & services and select the integration card.
  2. Next to the entry you want to remove, select the three dots menu. Then, select Delete.
    • Depending on the integration, the entries are listed under one of the following headings:
      • Devices
      • Hubs
      • Services
      • Integration entries
  3. To confirm, select Delete.
    • Home Assistant also deletes the devices and entities of the entry.
  4. If Home Assistant asks you to restart, restart Home Assistant.
  5. If Home Assistant asks whether to also delete the application credentials, select Remove or Keep.